Some States require that you have several different identification labels on your car. Police have a much easier time recognizing vehicles when the details of that car are readily visible. A front license plate is required in certain States, and not having one attached can cause you to get a ticket. The Honda Civic is one of the most popular cars in the country and it usually comes ready for a front plate installation. If you aren't sure how to attach the plate, you might need to first install a front mount.
Attach the Mount
FRONT LICENSE PLATE BRACKET INSTALLATION INSTRUCTIONS – Introduction – Helpful General Information to Read Before Installing All of our license plate brackets are designed and manufactured so they screw into the existing license plate mounting locations in the Toyota bumpers.
Step 1
Kneel down in front of your car and locate the four screws on your Civic bumper. These are located in the exact center of the car bumper. If you do not see any screws, then you might not have a front mount installed. If your state requires you to have a front plate license, then the Honda dealership will install one for free. Other places charge a small fee, but you can also install it yourself.
Step 2
Locate the two holes in the underside of the front bumper. The mount will attach to these holes.
Step 3
Line up the mount to the two holes. If the mount came with washers, put those in between the mount and the screw. Washers are used to keep the screw from tearing up the mount (or the plate).
Tighten the screws into the mount so that it securely attaches to the front bumper.
Install Front License Plate Bracket Nissan Murano
Attach the Plate
Step 1
Take your screwdriver and remove the screws (if you just installed a new mount, skip to step 3). Turn counterclockwise (twist left) to loosen the screws. Set the screws aside in a cup or bag so that they do not accidentally roll away.
Step 2
Remove any old plate that might be attached. Sometimes the dealership will put a fake plate there temporarily. If so, remove the attached plate and set aside. There also might be old washers on the screws. If so, hold on to them.
Step 3
Match up the plate to the four holes to be sure everything will fit.
Place the washer in front of the hole on the plate face, and insert the screws. Use the screwdriver to tighten up the plate. Repeat this process for all four screws. The plate should be touching the bumper, and the washers should be in between the plate and the screw heads. Openvpn setup for windows xp.
Items you will need
Front plate mount
Front license plate
Screwdriver
license plates image by timur1970 from Fotolia.com
More Articles
Some states require license plates on both the front and the back of a vehicle. Not all vehicles are equipped with a front license plate bracket. Brackets are made with the contours of a bumper in mind. When the bracket is installed properly, spacers are first attached to the bumper and then the bracket is attached to the spacers.
Install Front License Plate Bracket
Step 1
Measure the front bumper from side to side using a tape measure to find the center.
Step 2
Measure the front bumper from the top of the bumper to its bottom.
Step 3
Place the license plate bracket on the center mark so that its four corners are centered from side to side and from top to bottom on the bumper.
Step 4
Step 5
Push a pen through each of the four corner holes of the bracket and place guide marks on the bumper.
Step 6
Step 7
Pre-drill 1/8-inch deep guide holes at each of the four corner marks using an electric drill with an 1/8-inch bit.
Step 8
Place the bracket back on the bumper so that it lines up with the four holes.
Step 9
Insert the four mounting screws that came with the bracket into the four holes.
FileOpen Client is a program developed by FileOpen Systems. Adobe plugin download. The most used version is 3.0.16.879, with over 98% of all installations currently using this version.
Step 10
Screw the screws down until the bracket is secured to the bumper.
Step 11
Step 12
Insert the four corner screws through the four holes in the plate that hold the plate to the bracket.